TL-FC111B is a 100 Gigabit single-mode single-fiber optical fiber transceiver, which provides a 100 Gigabit electrical port and a 100 Gigabit SC optical port, which can convert the electrical port signal to the optical port signal and carry out long-distance data transmission through optical fiber. The TL-FC111B uses wavelength division multiplexing technology, with a transmit wavelength of 1310nm and a receive wavelength of 1550nm, to receive and transmit data simultaneously through a single-mode optical fiber, with a maximum transmission distance of 20 km. TL-FC111B is recommended to be used in conjunction with TL-FC111A to give full play to the product performance. 1 x 100 Gigabit SC optical port, 1 x 100 Gigabit RJ45 network port Based on wavelength division multiplexing technology, single-mode and single-fiber transmission, the maximum transmission distance is 20 kilometers Operating wavelength: 1310nm (transmit), 1550nm (receive)

TL-FC114B is a 100 Gigabit single-mode single-fiber optical fiber transceiver, providing 4 100 Gigabit electrical ports and 1 100 Gigabit SC optical port, which can convert electrical port signals to optical port signals and conduct long-distance data transmission through optical fibers. The TL-FC114B uses wavelength division multiplexing technology, with a transmit wavelength of 1310nm and a receive wavelength of 1550nm, receiving and sending data simultaneously through a single mode optical fiber, with a maximum transmission distance of 20 km. TL-FC114B is recommended to be used in conjunction with TL-FC111A to give full play to product performance. 1 x 100 Gigabit SC optical port, 4 x 100 Gigabit RJ45 network port Based on wavelength division multiplexing technology, single-mode and single-fiber transmission, the maximum transmission distance is 20 kilometers Operating wavelength: 1310nm (transmit), 1550nm (receive)

The TL-FC311A-3 is a gigabit single-mode single-fiber optical fiber transceiver that provides a 1000Mbps electrical port and a 1.25Gbps SC optical port, which can convert the electrical port signal to the optical port signal and transmit data over long distances through optical fiber. The TL-FC311A-3 uses wavelength division multiplexing technology, with a transmit wavelength of 1550nm and a receive wavelength of 1310nm, and receives and transmits data simultaneously through a single-mode optical fiber, with a maximum transmission distance of 3 km. TL-FC311A-3 is recommended to be used in conjunction with TL-FC311B-3 to give full play to the product performance. 1 Gigabit SC optical port, 1 Gigabit RJ45 network port Based on wavelength division multiplexing technology, single-mode and single-fiber transmission, the maximum transmission distance is 3 kilometers Operating wavelength: 1550nm (transmit), 1310nm (receive)

The TL-FC311B-3 is a Gigabit single-mode single-fiber optical fiber transceiver, providing a 1000Mbps electrical port and a 1.25Gbps SC optical port, which can convert the electrical port signal to the optical port signal and carry out long-distance data transmission through optical fiber. TL-FC311B-3 adopts wavelength division multiplexing technology, transmit wavelength 1310nm, receive wavelength 1550nm, receive and transmit data through a single-mode optical fiber at the same time, and the maximum transmission distance is 3 km. TL-FC311B-3 is recommended to be used in conjunction with TL-FC311A-3 to give full play to the product performance. 1 Gigabit SC optical port, 1 Gigabit RJ45 network port Based on wavelength division multiplexing technology, single-mode and single-fiber transmission, the maximum transmission distance is 3 kilometers Operating wavelength: 1310nm (transmit), 1550nm (receive)

TL-FC314B-3 is a gigabit single-mode single-fiber optical fiber transceiver, providing four 1000Mbps electrical ports and one 1.25Gbps SC optical port, which can convert electrical port signals to optical port signals and conduct long-distance data transmission through optical fibers. The TL-FC314B-3 uses wavelength division multiplexing technology, with a transmit wavelength of 1310nm and a receive wavelength of 1550nm, which receives and transmits data simultaneously through a single-mode optical fiber, with a maximum transmission distance of 3 km. TL-FC314B-3 is recommended to be used in conjunction with TL-FC311A-3 to give full play to the product performance. 1 Gigabit SC optical port, 4 Gigabit RJ45 network ports Based on wavelength division multiplexing technology, single-mode and single-fiber transmission, the maximum transmission distance is 3 kilometers Operating wavelength: 1310nm (transmit), 1550nm (receive)

The TL-POE10R is a self-developed PoE separator developed by TP-LINK, which complies with the IEEE 802.3af standard and can separate the power and data signals transmitted over the network cable. The TL-POE10R can be used in conjunction with IEEE 802.3af-compliant power supply devices (such as TP-LINK's TL-POE150S, TL-SF1008P, and TL-SG3424P) to provide data and power for network devices that do not support PoE. TL-POE10R can output 5V/9V/12V three voltages, and can be used with power supply equipment, which can flexibly expand home and office networks without being limited by the layout of power lines. IEEE 802.3af compliant It provides 5V/9V/12VDC three-step output The maximum transmission distance is up to 100 meters Gigabit Ethernet port Plug and play, no management required

TL-POE170S is a PoE power supply device independently developed by TL-LINK, which conforms to the IEEE 802.3af/at standard, and can load electric energy on the network cable for transmission, with a maximum transmission distance of 100m. The TL-POE170S automatically detects and identifies IEEE 802.3af/at compliant powered devices and automatically matches the output power to power them. IEEE 802.3af/at compliant The maximum output power is up to 30W The maximum power supply distance is up to 100m Automatically detect and identify the powered device and automatically match the output power Gigabit Ethernet port External 53.5V power adapter Plug and play, no management required

TL-SF1005 Industrial Grade is a TP-LINK Industrial Ethernet switch designed for industrial environments. Provides 5 100 Gigabit adaptive Ethernet interfaces. Provides 5 x 10/100M adaptive RJ45 ports Industrial working temperature: -40°C~75°C Wide voltage input: 9.6V~60VDC Small size (115 mm *70 mm *28 mm), better adaptable to industrial environment Multiple installation methods: rail installation + wall mounting IP30 protection: reduce the impact of dust VLAN and broadcast storm suppression switches are provided to adapt to various complex network environments Aluminum alloy shell, sturdy and durable Three-way power input, redundant backup, greatly improve the reliability of product power supply EMC high protection level, not afraid of all kinds of harsh environments *The industrial switch is not equipped with a power supply at the factory, if you need to use the power supply, please purchase it separately It is recommended to buy our industrial-grade power supply: TL-IP75-24 or TL-IP75D-24 -40°C~75°C working temperature design, no fear of extreme temperatures TL-SF1005 industrial grade is designed in strict accordance with the working temperature of -40°C~75°C, selects industrial-grade devices, and adopts natural heat dissipation mode to ensure that the equipment works stably for a long time in this temperature range and meets all kinds of harsh environments. Industrial-grade protection design High-standard electromagnetic anti-interference protection design, suitable for various harsh electromagnetic environments such as electric power and industrial plants. Aluminum alloy shell and electroless nickel gold PCB board greatly improve the anti-corrosion performance of the equipment. The housing can be protected by IP30 to reduce the impact of dust on the normal operation of the equipment. 9.6V~60VDC wide voltage input, multiple power protection It supports simultaneous access of three power supplies, and the power supply is redundant to ensure the uninterrupted work of the equipment. It supports a wide voltage input of 9.6V~60VDC, and is suitable for various industrial power supplies. Three types of power protection are provided to greatly improve the reliability of power supply to the switch. Featured devices The PCB board is made of electroless nickel gold plate, which has high corrosion resistance, oxidation resistance, and excellent electrical properties. Select high-specification and long-life Japanese capacitors to greatly improve the service life of the product. The circuit design of the highly redundant system avoids the sudden change of the external environment from affecting the normal operation of the equipment. TP-LINK's rigorous industrial-grade production and testing process is adopted to effectively release the electrical stress of components and greatly improve the reliability of equipment. Compact body design, metal shell, efficient heat dissipation The size of the fuselage is only 115mm*70mm*28mm, which can be very convenient to place in a compact work cabinet, and the high thermal conductivity aluminum alloy shell has better heat dissipation effect. DIN rail installation is easy and flexible The TL-SF1005 industrial grade can be easily installed on DIN rail and wall mounted, and the installation method can be flexibly selected according to needs, making the use of industrial-grade Ethernet switches simple and reliable. Excellent device compatibility TP-LINK has more than 100 million Ethernet switch devices running all over the world, serving all walks of life, ensuring that TP-LINK Ethernet switches can be compatible with all kinds of network equipment and production equipment.

TL-SF1005+ is a molded case 5-port 100 Gigabit Ethernet switch, providing 5 x 10/100M adaptive RJ45 ports, all ports support wire-speed forwarding and MDI/MDIX auto-flip function, plug and play. Provide 5 x 10/100M adaptive RJ45 ports LED panel indicator to dynamically display device connection and operation status The port supports automatic flipping, which is more convenient to use MAC address self-learning is supported Port performance Five 10/100M adaptive RJ45 ports are provided, and all ports can achieve wire-speed forwarding. Each port supports MDI/MDIX auto-rollover and duplex/rate auto-negotiation; Supports IEEE 802.3x full-duplex flow control and backpressure half-duplex flow control. Small and exquisite, simple and stylish It adopts a simple and elegant square case design, the length is slightly shorter than that of the iPhone 4, and the body is small and exquisite. Featuring off-white tones, the exquisite R-angle curvature has been treated with first-class polishing technology to show excellent texture and comfortable feel. Simple to use Plug-and-play, no management required, dynamic LED indicators provide simple working status prompts and troubleshooting.

TL-SF1005M is a 5-port 100 Gigabit Ethernet switch with a molded case, providing five 10/100M adaptive RJ45 ports, all ports support wire-speed forwarding and MDI/MDIX auto-flip function, plug and play. Provide 5 x 10/100M adaptive RJ45 ports Molded case body, small and exquisite The two-color injection molding process reflects technology and beauty LED panel indicator to dynamically display device connection and operation status The port supports automatic flipping, which is more convenient to use MAC address self-learning is supported High-speed transmission, stable online Five 10/100M adaptive RJ45 ports are provided, and all ports can achieve wire-speed forwarding. Enterprise-level standards are used to build traffic switches, with comprehensive performance optimization and overall product performance. Each port supports MDI/MDIX auto-rollover and duplex/rate auto-negotiation; Supports IEEE 802.3x full-duplex flow control and backpressure half-duplex flow control. Small and exquisite, two-color injection molding Adopt a square shell design, uphold the simple design philosophy; The body size is only 72mm x 65mm x 24.5mm, and the length of the body is smaller than that of a bank card, saving users every inch of space; Creative Germany introduces two-color injection molding process, and the surface is crystal clear like a feather coat; Versatile mist gray is selected, and the color is calm and elegant like gray lead; Polishing the perfect R angle arc, the feel is delicate and comfortable like jade; Innovative craftsmanship and design aesthetics complement each other, reflecting the perfect combination of technology and beauty. plug and play Plug-and-play, no management required, dynamic LED indicators provide simple working status prompts and troubleshooting.

TL-SF1005P is an unmanaged PoE switch independently developed by TP-LINK, with 4 100 Gigabit ports supporting PoE+ power supply, compliant with IEEE 802.3af/at standard, with a single-port PoE power of up to 30W and a maximum PoE output power of 62W. As a PoE power supply device, it can automatically detect and identify the powered device that meets the standard and supply it with network cables. Plug-and-play, no configuration required, simple and convenient to use, meet the needs of high-density PoE power supply network environment, suitable for hotels, campuses, factory dormitories, small and medium-sized enterprises to build a cost-effective network. 5 x 10/100M adaptive RJ45 ports, ports 1~4 support IEEE 802.3af/at standard PoE power supply The single-port POE power can reach 30W, and the maximum PoE output power of the whole machine is 62W Supports IEEE802.3X full-duplex flow control and backpressure half-duplex flow control Auto MDI/MDIX is supported All ports are capable of wire-speed forwarding All 100 megabits Five 10/100 Base-T RJ45 ports are available. All ports support non-blocking wire-speed forwarding for smoother transmission. Supports IEEE 802.3x full-duplex flow control and backpressure half-duplex flow control. PoE power supply function Four 10/100 Base-T RJ45 ports support PoE+ power supply to meet the requirements of PoE power supply in scenarios such as visual security, teleconferencing systems, and wireless coverage. In line with the IEEE 802.3af/at PoE power supply standard, the maximum PoE output power of the whole machine is 62W, and the maximum PoE output power of a single port is 30W. Automatically identify PoE devices for power supply without damaging non-PoE devices. When the output power of the whole device exceeds the standard, the PoE port will be disconnected from the power supply of the last power-on port to prevent the device from overloading. The equipment is stable and reliable The low-power design of the host and the fan strengthen the heat dissipation to ensure the stable operation of the product. It adopts TP-LINK's self-developed power supply and high redundancy design to provide long-term and stable PoE power output. It's easy to use Plug and play, no configuration required, simple and convenient. Users can easily understand the working status of the device through the power indicator (Power) and port status indicator (Link/Act).

TL-SF1006LP is an unmanaged PoE switch independently developed by TP-LINK, with 4 100 Gigabit ports supporting PoE+ power supply, complying with IEEE 802.3af/at standard, with a single-port PoE power of 30W and a maximum PoE output power of 41W. As a PoE power supply device, it can automatically detect and identify the powered device that meets the standard and supply it with network cables. Plug-and-play, no configuration required, simple and convenient to use, meet the needs of high-density PoE power supply network environment, suitable for hotels, campuses, factory dormitories, small and medium-sized enterprises to build a cost-effective network. 6 x 10/100M adaptive RJ45 ports, ports 1~4 support IEEE 802.3af/at standard PoE power supply The single-port POE power can reach 30W, and the maximum PoE output power of the whole machine is 41W Supports IEEE802.3X full-duplex flow control and backpressure half-duplex flow control Auto MDI/MDIX is supported All ports are capable of wire-speed forwarding All 100 megabits Six 10/100 Base-T RJ45 ports are available. All ports support non-blocking wire-speed forwarding for smoother transmission. Supports IEEE 802.3x full-duplex flow control and backpressure half-duplex flow control. PoE power supply function Four 10/100 Base-T RJ45 ports support PoE+ power supply to meet the requirements of PoE power supply in scenarios such as visual security, teleconferencing systems, and wireless coverage. In line with IEEE 802.3af/at PoE power supply standard, the maximum PoE output power of the whole machine is 41W, and the maximum PoE output power of a single port is 30W. Automatically identify PoE devices for power supply without damaging non-PoE devices. The equipment is stable and reliable The low-power design of the host and the fan strengthen the heat dissipation to ensure the stable operation of the product. It adopts TP-LINK's self-developed power supply and high redundancy design to provide long-term and stable PoE power output. It's easy to use Plug and play, no configuration required, simple and convenient. Users can easily understand the working status of the device through the power indicator (Power) and port status indicator (Link/Act).

TL-SF1006PM is an unmanaged PoE switch independently developed by TP-LINK, with 4 100 Gigabit ports supporting PoE+ power supply, in line with IEEE 802.3af/at standard, with a single-port PoE power of 30W and a maximum PoE output power of 41W. As a PoE power supply device, it can automatically detect and identify the powered device that meets the standard and supply it with network cables. Plug-and-play, no configuration required, simple and convenient to use, meet the needs of high-density PoE power supply network environment, suitable for hotels, campuses, factory dormitories, small and medium-sized enterprises to build a cost-effective network. 6 x 10/100M adaptive RJ45 ports, ports 1~4 support IEEE 802.3af/at standard PoE power supply The single-port POE power can reach 30W, and the maximum PoE output power of the whole machine is 41W Supports IEEE802.3X full-duplex flow control and backpressure half-duplex flow control Auto MDI/MDIX is supported All ports are capable of wire-speed forwarding All 100 megabits Six 10/100 Base-T RJ45 ports are available. All ports support non-blocking wire-speed forwarding for smoother transmission. Supports IEEE 802.3x full-duplex flow control and backpressure half-duplex flow control. PoE power supply function Four 10/100 Base-T RJ45 ports support PoE+ power supply to meet the requirements of PoE power supply in scenarios such as visual security, teleconferencing systems, and wireless coverage. In line with IEEE 802.3af/at PoE power supply standard, the maximum PoE output power of the whole machine is 41W, and the maximum PoE output power of a single port is 30W. Automatically identify PoE devices for power supply without damaging non-PoE devices. The equipment is stable and reliable The low-power design of the host and the fan strengthen the heat dissipation to ensure the stable operation of the product. It adopts TP-LINK's self-developed power supply and high redundancy design to provide long-term and stable PoE power output. It's easy to use Plug and play, no configuration required, simple and convenient. Users can easily understand the working status of the device through the power indicator (Power) and port status indicator (Link/Act).

TL-SF1008 Industrial Grade is a TP-LINK Industrial Ethernet switch designed for industrial environments. Provides 8 100 Gigabit adaptive Ethernet interfaces. Provides 8 x 10/100M adaptive RJ45 ports Industrial working temperature: -40°C~75°C Wide voltage input: 9.6V~60VDC Small size (137 mm *100 mm *38 mm), better adaptable to industrial environment Multiple installation methods: rail installation + wall mounting IP30 protection: reduce the impact of dust VLAN and broadcast storm suppression switches are provided to adapt to various complex network environments Aluminum alloy shell, sturdy and durable Three-way power input, redundant backup, greatly improve the reliability of product power supply EMC high protection level, not afraid of all kinds of harsh environments *The industrial switch is not equipped with a power supply at the factory, if you need to use the power supply, please purchase it separately It is recommended to buy our industrial-grade power supply: TL-IP75-24 or TL-IP75D-24 -40°C~75°C working temperature design, no fear of extreme temperatures TL-SF1008 industrial-grade Ethernet switch is designed in strict accordance with the working temperature of -40°C~75°C, selects industrial-grade devices, and adopts natural heat dissipation mode to ensure that the equipment works stably for a long time in this temperature range and meets all kinds of harsh environments. Industrial-grade protection design High-standard electromagnetic anti-interference protection design, suitable for various harsh electromagnetic environments such as electric power and industrial plants. Aluminum alloy shell and electroless nickel gold PCB board greatly improve the anti-corrosion performance of the equipment. The housing can be protected by IP30 to reduce the impact of dust on the normal operation of the equipment. 9.6V~60VDC wide voltage input, multiple power protection It supports simultaneous access of three power supplies, and the power supply is redundant to ensure the uninterrupted work of the equipment. It supports a wide voltage input of 9.6V~60VDC, and is suitable for various industrial power supplies. Three types of power protection are provided to greatly improve the reliability of power supply to the switch. Featured devices The PCB board is made of electroless nickel gold plate, which has high corrosion resistance, oxidation resistance, and excellent electrical properties. Select high-specification and long-life Japanese capacitors to greatly improve the service life of the product. The circuit design of the highly redundant system avoids the sudden change of the external environment from affecting the normal operation of the equipment. TP-LINK's rigorous industrial-grade production and testing process is adopted to effectively release the electrical stress of components and greatly improve the reliability of equipment. Compact body design, metal shell, efficient heat dissipation The size of the fuselage is only 137mm*100mm*38mm, which can be very convenient to place in a compact work cabinet, and the high thermal conductivity aluminum alloy shell has better heat dissipation effect. DIN rail installation is easy and flexible The TL-SF1008 industrial grade can be easily installed on DIN rail and wall mounted, and the installation method can be flexibly selected according to needs, making the use of industrial-grade Ethernet switches simple and reliable. Excellent device compatibility TP-LINK has more than 100 million Ethernet switch devices running all over the world, serving all walks of life, ensuring that TP-LINK Ethernet switches can be compatible with all kinds of network equipment and production equipment.

TL-SF1008+ is a molded case 8-port 100 Gigabit Ethernet switch, providing 8 x 10/100M adaptive RJ45 ports, all ports support wire-speed forwarding and MDI/MDIX auto-flip function, plug and play. Eight 10/100M adaptive RJ45 ports are provided LED dynamic indicators for easy status indication and troubleshooting It supports automatic port flipping, which is more convenient to use MAC address self-learning is supported It is close to the people and practical, and has superior performance Eight 10/100M adaptive RJ45 ports are provided, and all ports can achieve wire-speed forwarding. Enterprise-level standards are used to build traffic switches, with comprehensive performance optimization and overall product performance. Each port supports MDI/MDIX auto-rollover and duplex/rate auto-negotiation; Supports IEEE 802.3x full-duplex flow control and backpressure half-duplex flow control. Small and exquisite, simple and stylish The diffusion corrugated design created with heart flows through the sense of science and technology at the fingertips. With a body size of 140mm x 66.4mm x 27.6mm, the mini is compact and space-saving. Simple to use Plug-and-play, no management required, dynamic LED indicators provide simple working status prompts and troubleshooting.

TL-SF1008D is a steel-shelled 8-port 100 Gigabit Ethernet switch with 8 x 10/100M adaptive RJ45 ports, all ports support wire-speed forwarding and MDI/MDIX auto-flip function, plug and play. Eight 10/100M adaptive RJ45 ports are provided The steel shell body is small and exquisite LED dynamic indicators for easy status indication and troubleshooting It supports automatic port flipping, which is more convenient to use MAC address self-learning is supported A practical choice with superior performance Eight 10/100M adaptive RJ45 ports are provided, and all ports can achieve wire-speed forwarding. Enterprise-level standards are used to build traffic switches, with comprehensive performance optimization and overall product performance. Each port supports MDI/MDIX auto-rollover and duplex/rate auto-negotiation; Supports IEEE 802.3x full-duplex flow control and backpressure half-duplex flow control. The steel shows its true color and is of outstanding quality The steel shell is used to better shield interference, better heat dissipation, and ensure the stable operation of the equipment for a long time. Square design, sharp edges, outstanding quality, compact body, space-saving. plug and play Plug-and-play, no management required, dynamic LED indicators provide simple working status prompts and troubleshooting.

TL-SF1008VE is an 8-port VLAN switch product developed by Pulian Technology Co., Ltd. for the network of residential areas, urban villages and small and medium-sized enterprises, providing 8 10/100M Ethernet ports, plug and play, and hardware VLAN switch and loop monitoring functions to meet the needs of isolation and troubleshooting at the network access layer. 8 x 10/100M adaptive RJ45 ports Support VLAN switch control Support loop monitoring function, timely feedback loop faults Supports IEEE802.3X full-duplex flow control and backpressure half-duplex flow control Auto MDI/MDIX is supported Supports self-learning and aging of MAC addresses 8 100 Gigabit ports, plug and play Eight 10/100M adaptive RJ45 ports are provided, and all ports can achieve wire-speed forwarding. Each port supports MDI/MDIX auto-rollover and duplex/rate auto-negotiation; Support IEEE 802.3x full-duplex flow control and backpressure half-duplex flow control; Plug-and-play, no management required, dynamic LED indicators provide simple working status alerts. One-click VLAN switching Hardware VLAN switches are provided, which can be flexibly switched according to the needs of the actual environment. When the VLAN function is enabled, ports 1-7 cannot access each other and can only communicate with port 8 to isolate ports, suppress network storms, and improve network security. When the VLAN function is disabled, eight ports can communicate with each other. Loop monitoring Built-in loop monitoring function, after a loop fault occurs, the loop alarm indicator and the corresponding fault port indicator flash at the same frequency, reminding the user to eliminate the loop fault in real time and restore the normal operation of the network.

TL-SF1009P is an unmanaged PoE switch independently developed by TP-LINK, with 8 100 Gigabit ports supporting IEEE 802.3af/at standard PoE+ power supply, a single-port PoE power of up to 30W, and the maximum PoE output power of the whole machine is increased to 62W. As a PoE power supply device, it can automatically detect and identify the powered device that meets the standard and supply it with network cables. Plug-and-play, no configuration required, simple and convenient to use, meet the needs of high-density PoE power supply network environment, suitable for hotels, campuses, factory dormitories, small and medium-sized enterprises to build a cost-effective network. Eight 10/100 Base-T RJ45 ports support PoE power supply 1 x 10/100 Base-T RJ45 uplink port The PoE power supply power of the whole machine is increased to 62W, and the PoE power supply power of a single port reaches 30W Supports IEEE 802.3af/at PoE power supply standard PoE power delivery ports support the priority mechanism The housing supports wall-mounted holes All 100 megabits Nine 10/100 Base-T RJ45 ports are available. All ports support non-blocking wire-speed forwarding for smoother transmission. Supports IEEE 802.3x full-duplex flow control and backpressure half-duplex flow control. PoE power supply function Eight 10/100 Base-T RJ45 ports support PoE power supply to meet the requirements of PoE power supply in scenarios such as visual security, teleconferencing systems, and wireless coverage. In line with the IEEE 802.3af/at PoE power supply standard, the maximum PoE output power of the whole machine is increased to 62W, and the maximum PoE output power of a single port is 30W. Automatically identify PoE devices for power supply without damaging non-PoE devices. PoE ports support a priority mechanism to ensure the power supply of high-priority ports when the remaining power is insufficient, so as to prevent devices from overloading. The equipment is stable and reliable The low-power design of the host has good heat dissipation to ensure the stable operation of the product. It adopts TP-LINK's self-developed power supply and high redundancy design to provide long-term and stable PoE power output. It's easy to use Plug and play, no configuration required, simple and convenient. Users can easily understand the working status of the device through the power indicator (Power) and port status indicator (Link/Act).

TL-SF1009PE is an unmanaged PoE switch independently developed by TP-LINK, with 8 100 Gigabit ports supporting PoE+ power supply, in line with IEEE 802.3af/at standard, with a single port PoE power of up to 30W and a maximum PoE output power of 125W. As a PoE power supply device, it can automatically detect and identify the powered device that meets the standard and supply it with network cables. Plug-and-play, no configuration required, simple and convenient to use, meet the needs of high-density PoE power supply network environment, suitable for hotels, campuses, factory dormitories, small and medium-sized enterprises to build a cost-effective network. Eight 10/100 Base-T RJ45 ports support PoE+ power supply 1 x 10/100 Base-T RJ45 uplink port The PoE power supply power of the whole machine is up to 125W, and the PoE power supply power of a single port is up to 30W PoE power delivery ports support the priority mechanism All 100 megabits Nine 10/100 Base-T RJ45 ports are available. All ports support non-blocking wire-speed forwarding for smoother transmission. Supports IEEE 802.3x full-duplex flow control and backpressure half-duplex flow control. PoE power supply function Eight 10/100 Base-T RJ45 ports support PoE+ power supply to meet the needs of PoE power supply in scenarios such as visual security, teleconferencing systems, and wireless coverage. In line with the IEEE 802.3af/at PoE power supply standard, the maximum PoE output power of the whole machine is 125W, and the maximum PoE output power of a single port is 30W. Automatically identify PoE devices for power supply without damaging non-PoE devices. PoE ports support a priority mechanism to ensure the power supply of high-priority ports when the remaining power is insufficient, so as to prevent devices from overloading. The equipment is stable and reliable The low-power design of the host and the fan strengthen the heat dissipation to ensure the stable operation of the product. It adopts TP-LINK's self-developed power supply and high redundancy design to provide long-term and stable PoE power output. The equipment meets the national CCC standard, fully meets the safety requirements, and is safe and reliable to use. It's easy to use Plug and play, no configuration required, simple and convenient. Users can easily understand the working status of the device through the power indicator (Power) and port status indicator (Link/Act).

TL-SF1010D is a 10-port 100 Gigabit Ethernet switch product developed by Pulian Technology Co., Ltd. for small visual security environment, providing 8 x 10/100M common ports and 2 x 10/100M uplink ports, which can meet the networking needs of 8-channel or 4-channel visual security network with only one switch. 10 x 10/100M adaptive RJ45 ports to meet the networking requirements of small visual security environments Auto MDI/MDIX is supported Support MAC address self-learning and full-duplex working mode Plug and play, no management required Tabletop housing with wall-mounted holes for flexible deployment 10 100 Gigabit ports for small visual security networks 8 x 10/100M common ports and 2 x 10/100M uplink ports; Only one switch is needed to meet the networking needs of 8-channel or 4-channel visual security networking Each port supports MDI/MDIX auto-rollover and duplex/rate auto-negotiation; Supports IEEE 802.3x full-duplex flow control and backpressure half-duplex flow control. Plug and play, simple to use, flexible deployment Plug and play, no management required; Dynamic LED indicator provides simple working status prompts and troubleshooting methods; The tabletop housing is also available with wall-mounted holes for flexible deployment as needed.

TL-SF1010P is an unmanaged PoE switch independently developed by TP-LINK, with 8 100 Gigabit ports supporting IEEE 802.3af/at standard PoE+ power supply, a single port PoE power of up to 30W, and the maximum PoE output power of the whole machine is increased to 72W. As a PoE power supply device, it can automatically detect and identify the powered device that meets the standard and supply it with network cables. Plug-and-play, no configuration required, simple and convenient to use, meet the needs of high-density PoE power supply network environment, suitable for hotels, campuses, factory dormitories, small and medium-sized enterprises to build a cost-effective network. Eight 10/100 Base-T RJ45 ports support PoE power supply Two 10/100 Base-T RJ45 uplink ports The PoE power supply power of the whole machine is increased to 72W, and the PoE power supply power of a single port reaches 30W Supports IEEE 802.3af/at PoE power supply standard PoE power delivery ports support the priority mechanism The housing supports wall-mounted holes All 100 megabits Provides 10 x 10/100 Base-T RJ45 ports. All ports support non-blocking wire-speed forwarding for smoother transmission. Supports IEEE 802.3x full-duplex flow control and backpressure half-duplex flow control. PoE power supply function Eight 10/100 Base-T RJ45 ports support PoE power supply to meet the requirements of PoE power supply in scenarios such as visual security, teleconferencing systems, and wireless coverage. In line with the IEEE 802.3af/at PoE power supply standard, the maximum PoE output power of the whole machine is increased to 62W, and the maximum PoE output power of a single port is 30W. Automatically identify PoE devices for power supply without damaging non-PoE devices. PoE ports support a priority mechanism to ensure the power supply of high-priority ports when the remaining power is insufficient, so as to prevent devices from overloading. The equipment is stable and reliable The low-power design of the host has good heat dissipation to ensure the stable operation of the product. It adopts TP-LINK's self-developed power supply and high redundancy design to provide long-term and stable PoE power output. The equipment meets the national CCC standard, fully meets the safety requirements, and is safe and reliable to use. It's easy to use Plug and play, no configuration required, simple and convenient. Users can easily understand the working status of the device through the power indicator (Power) and port status indicator (Link/Act).

TL-SF1010P is a steel-shell unmanaged PoE switch independently developed by TP-LINK, with 8 100 Gigabit ports supporting PoE power supply, in line with IEEE 802.3at/af standard, with a single-port PoE power of 30W and a maximum PoE output power of 62W. As a PoE power supply device, it can automatically detect and identify the powered device that meets the standard and supply it with network cables. Plug-and-play, no configuration required, simple and convenient to use, meet the needs of high-density PoE power supply network environment, suitable for hotels, campuses, factory dormitories, small and medium-sized enterprises to build a cost-effective network. 10 x 10/100M adaptive RJ45 ports, ports 1~8 support IEEE 802.3at/af standard PoE power supply The single-port POE power can reach 30W, and the maximum PoE output power of the whole machine is 62W Supports IEEE802.3X full-duplex flow control and backpressure half-duplex flow control Auto MDI/MDIX is supported PoE ports support a prioritization mechanism All 100 megabits Provides 10 x 10/100 Base-T RJ45 ports. All ports support non-blocking wire-speed forwarding for smoother transmission. Supports IEEE 802.3x full-duplex flow control and backpressure half-duplex flow control. PoE power supply function Eight 10/100 Base-T RJ45 ports support PoE power supply to meet the requirements of PoE power supply in scenarios such as visual security, teleconferencing systems, and wireless coverage. It complies with the IEEE 802.3at/af PoE power supply standard, and the maximum PoE output power of the whole machine is 62W, and the maximum PoE output power of a single port is 30W. Automatically identify PoE devices for power supply without damaging non-PoE devices. PoE ports support a priority mechanism to ensure the power supply of high-priority ports when the remaining power is insufficient, so as to prevent devices from overloading. It's easy to use Plug and play, no configuration required, simple and convenient. Users can easily understand the working status of the device through the power indicator (Power) and port status indicator (Link/Act).

TL-SF1016D is a desktop Layer 2 100 Gigabit unmanaged Ethernet switch product developed by TP-LINK, providing 16 x 10/100M adaptive RJ45 ports, all ports support wire-speed forwarding and MDI/MDIX auto-flip function, plug and play, no management required. 16 x 10/100M adaptive RJ45 ports All ports support wire-speed data forwarding Auto MDI/MDIX is supported Energy-saving technology is used to effectively save energy consumption and extend product life MAC address self-learning is supported The low-power fanless design eliminates noise interference and improves product stability Desktop-mounted, rack-mountable, plug-and-play, no management required Port performance 16 x 10/100M adaptive RJ45 ports, all ports can achieve wire-speed forwarding. Each port supports MDI/MDIX auto-rollover and duplex/rate auto-negotiation; Supports IEEE 802.3x full-duplex flow control and backpressure half-duplex flow control. Energy saving and environmental protection Energy-saving technology is used to automatically adjust the signal strength by detecting the length of the network cable and the workload, effectively reducing energy consumption. Simple to use Desktop housing, easy to install, rack-mounted, plug-and-play, no management required, dynamic LED indicators, provide simple working status prompts and troubleshooting.

TL-SF1016M is a 16-port 100 Gigabit Ethernet switch with a molded case, providing 16 x 10/100M adaptive RJ45 ports, all ports support wire-speed forwarding and MDI/MDIX auto-flip function, plug and play. Provides 16 x 10/100M adaptive RJ45 ports LED dynamic indicators for easy status indication and troubleshooting It supports automatic port flipping, which is more convenient to use MAC address self-learning is supported Port performance 16 x 10/100M adaptive RJ45 ports, all ports can achieve wire-speed forwarding; Each port supports MDI/MDIX auto-rollover and duplex/rate auto-negotiation; Supports IEEE 802.3x full-duplex flow control and backpressure half-duplex flow control. Simple to use Plug-and-play, no management required, dynamic LED indicators provide simple working status prompts and troubleshooting.

TL-SF1016S is a Layer 2 unmanaged Ethernet switch product developed by TP-LINK, providing 16 x 10/100M adaptive RJ45 ports, all ports support wire-speed forwarding and MDI/MDIX auto-flip function, and support 19-inch rack mounting. 16 x 10/100M adaptive RJ45 ports All ports are capable of wire-speed forwarding Auto MDI/MDIX is supported Energy-saving technology is used to effectively save energy consumption and extend product life MAC address self-learning is supported The low-power fanless design eliminates noise interference and improves product stability Standard rack mounting, plug and play, no management required Port performance 16 x 10/100M adaptive RJ45 ports, all ports can achieve wire-speed forwarding. Each port supports MDI/MDIX auto-rollover and duplex/rate auto-negotiation; Supports IEEE 802.3x full-duplex flow control and backpressure half-duplex flow control. Energy saving and environmental protection Energy-saving technology is used to automatically adjust the signal strength by detecting the length of the network cable and the workload, effectively reducing energy consumption. Simple to use The 19-inch standard rack-mount is plug-and-play and requires no management, and dynamic LED indicators provide simple working status prompts and troubleshooting.

TL-SF1024D is a desktop Layer 2 100 Gigabit unmanaged Ethernet switch developed by TP-LINK, providing 24 x 10/100M adaptive RJ45 ports, all ports support wire-speed forwarding and MDI/MDIX auto-flip function, plug-and-play, no management required. 24 x 10/100M adaptive RJ45 ports All ports support wire-speed data forwarding Auto MDI/MDIX is supported Energy-saving technology is used to effectively save energy consumption and extend product life MAC address self-learning is supported The low-power fanless design eliminates noise interference and improves product stability Desktop-mounted, rack-mountable, plug-and-play, no management required Port performance Provides 24 x 10/100M adaptive RJ45 ports, all of which can be forwarded at wire speed. Each port supports MDI/MDIX auto-rollover and duplex/rate auto-negotiation; Supports IEEE 802.3x full-duplex flow control and backpressure half-duplex flow control. Energy saving and environmental protection Energy-saving technology is used to automatically adjust the signal strength by detecting the length of the network cable and the workload, effectively reducing energy consumption. Simple to use Desktop housing, easy to install, rack-mounted, plug-and-play, no management required, dynamic LED indicators, provide simple working status prompts and troubleshooting.

TL-SG1005 Industrial Grade is TP-LINK's Industrial Ethernet Switch designed for industrial environments. Provides 5 Gigabit adaptive Ethernet interfaces. Provides 5 x 10/100/1000M adaptive RJ45 ports Industrial working temperature: -40°C~75°C Wide voltage input: 9.6V~60VDC Small size (137 mm *100 mm *38 mm), better adaptable to industrial environment Multiple installation methods: rail installation + wall mounting IP30 protection: reduce the impact of dust It provides WEB management, broadcast storm protection, and port interruption alarm switches to adapt to various complex network environments Aluminum alloy shell, sturdy and durable Three-way power input, redundant backup, greatly improve the reliability of product power supply EMC high protection level, not afraid of all kinds of harsh environments *The industrial switch is not equipped with a power supply at the factory, if you need to use the power supply, please purchase it separately It is recommended to buy our industrial-grade power supply: TL-IP75-24 or TL-IP75D-24 -40°C~75°C working temperature design, no fear of extreme temperatures TL-SG1005 industrial grade is designed in strict accordance with the working temperature of -40°C~75°C, selected industrial-grade devices, and adopts natural heat dissipation mode to ensure that the equipment works stably for a long time in this temperature range and meets all kinds of harsh environments. Industrial-grade protection design High-standard electromagnetic anti-interference protection design, suitable for various harsh electromagnetic environments such as electric power and industrial plants. Aluminum alloy shell and electroless nickel gold PCB board greatly improve the anti-corrosion performance of the equipment. The housing can be protected by IP30 to reduce the impact of dust on the normal operation of the equipment. 9.6V~60VDC wide voltage input, multiple power protection It supports simultaneous access of three power supplies, and the power supply is redundant to ensure the uninterrupted work of the equipment. It supports a wide voltage input of 9.6V~60VDC, and is suitable for various industrial power supplies. Three types of power protection are provided to greatly improve the reliability of power supply to the switch. Featured devices The PCB board is made of electroless nickel gold plate, which has high corrosion resistance, oxidation resistance, and excellent electrical properties. Select high-specification and long-life Japanese capacitors to greatly improve the service life of the product. The circuit design of the highly redundant system avoids the sudden change of the external environment from affecting the normal operation of the equipment. TP-LINK's rigorous industrial-grade production and testing process is adopted to effectively release the electrical stress of components and greatly improve the reliability of equipment. Compact body design, metal shell, efficient heat dissipation The size of the fuselage is only 137mm*100mm*38mm, which can be very convenient to place in a compact work cabinet, and the high thermal conductivity aluminum alloy shell has better heat dissipation effect. DIN rail installation is easy and flexible The TL-SG1005 industrial grade can be easily DIN rail mounted and wall-mounted, and the installation method can be flexibly selected according to needs, making the use of industrial-grade Ethernet switches simple and reliable. Excellent device compatibility TP-LINK has more than 100 million Ethernet switch devices running all over the world, serving all walks of life, ensuring that TP-LINK Ethernet switches can be compatible with all kinds of network equipment and production equipment. Port interrupt alarm, real-time monitoring of port working status The TL-SG1005 industrial grade provides port alarm function to monitor the working status of the port in real time. Once the port is disconnected, the alarm output of the terminal block will output an alarm signal, and the user will be alerted by the user's external alarm to the occurrence of port interruption. Simple and practical network management functions It supports the management and maintenance of the device through the web interface and PC management software. 802.1Q VLANs, MTU VLANs, and port VLANs are supported, allowing users to flexibly divide VLANs according to their needs. It supports QoS and three priority modes based on ports, 802.1P, and DSCP to optimize bandwidth configuration. Port aggregation is supported, which effectively increases link bandwidth, implements link backup, and improves link reliability. Port mirroring is supported, and data from a port is forwarded to the mirrored port for network monitoring. It supports bandwidth control, configures port data input/output transmission rates, and reasonably allocates and utilizes bandwidth. Storm suppression is supported to limit the broadcast traffic allowed to be received by the port to prevent broadcast storms from seriously slowing down network performance.

TL-SG1005M is a molded 5-port Gigabit Ethernet switch with five 10/100/1000M adaptive RJ45 ports, all ports support wire-speed forwarding and MDI/MDIX auto-flip function, plug and play. 5 x 10/100/1000M adaptive RJ45 ports All ports are capable of wire-speed forwarding Auto MDI/MDIX is supported Support MAC address self-learning and full-duplex working mode Desktop molded housing, plug and play, no management required Port performance Five 10/100/1000M adaptive RJ45 ports are provided, and all ports can achieve wire-speed forwarding. Each port supports MDI/MDIX auto-rollover and duplex/rate auto-negotiation; Supports IEEE 802.3x full-duplex flow control and backpressure half-duplex flow control. Simple to use Plug-and-play, no management required, dynamic LED indicators provide simple working status prompts and troubleshooting.

TL-SG1005P is an unmanaged PoE switch independently developed by TP-LINK, with 4 Gigabit ports supporting PoE+ power supply, complying with IEEE 802.3af/at standard, with a single-port PoE power of up to 30W and a maximum PoE output power of 60W. As a PoE power supply device, it can automatically detect and identify the powered device that meets the standard and supply it with network cables. Plug-and-play, no configuration required, simple and convenient to use, meet the needs of high-density PoE power supply network environment, suitable for hotels, campuses, factory dormitories, small and medium-sized enterprises to build a cost-effective network. 5 x 10/100/1000M adaptive RJ45 ports, ports 1~4 support IEEE 802.3af/at standard PoE power supply The single-port POE power can reach 30W, and the maximum PoE output power of the whole machine is 60W Supports IEEE802.3X full-duplex flow control and backpressure half-duplex flow control Auto MDI/MDIX is supported All ports are capable of wire-speed forwarding Rich port specifications Provides 5 x 10/100/1000M RJ45 ports. All ports support non-blocking wire-speed forwarding for smoother transmission. Supports IEEE 802.3x full-duplex flow control and backpressure half-duplex flow control. PoE power supply function It provides 4 PoE power supply ports and a PoE output power of 60W to meet the needs of PoE power supply networks such as home visual security and wireless coverage. It complies with the IEEE 802.3af/at PoE power supply standard, and the maximum PoE output power of a single port is 30W. Automatically identify PoE devices for power supply without damaging non-PoE devices. When the remaining power is insufficient, the PoE port will be prioritized to disconnect the power supply from the last power-on port to prevent the device from being overloaded. The equipment is stable and reliable The low-power design of the host has good heat dissipation to ensure the stable operation of the product. It adopts TP-LINK's self-developed power supply and high redundancy design to provide long-term and stable PoE power output. It's easy to use Plug and play, no configuration required, simple and convenient. Users can easily understand the working status of the device through the power indicator (Power) and port status indicator (Link/Act). Comply with network standards IEEE 802.3、IEEE 802.3u、IEEE 802.3x Compliant with IEEE 802.3af/at PoE power supply standard

TL-SG1005U is a newly designed molded case 5-port Gigabit Ethernet switch, providing 5 x 10/100/1000Mbps adaptive RJ45 ports, all ports support wire-speed forwarding and auto-rollover, plug and play. Provides 5 x 10/100/1000Mbps adaptive RJ45 ports All ports support wire-speed forwarding and automatic rollover Plug and play, no management required Tabletop plastic case, small and simple Two-color process, reflecting technology and beauty Port performance Five 10/100/1000M adaptive RJ45 ports are provided, and all ports can achieve wire-speed forwarding. Each port supports MDI/MDIX auto-rollover and duplex/rate auto-negotiation; Supports IEEE 802.3x full-duplex flow control and backpressure half-duplex flow control. Simple to use Plug-and-play, no management required, dynamic LED indicators provide simple working status prompts and troubleshooting. Two-tone craftsmanship, simple and exquisite Creatively introduced two-color injection molding process, the surface of the upper cover is crystal clear, and the polishing is perfect R angle arc, and the feel is delicate and comfortable like jade. Design aesthetics and innovative craftsmanship complement each other to give products a unique and stylish quality.